كروت صوت للهندسة الصوتيه -شو نوع الكرت اللي عندك؟

Sound Blaster X-Fi features an SRC (Sample Rate Conversion) engine that is 300 times more precise than the previous Sound Blaster solutions and can convert any audio to any resolution at near transparency with 136dB THD+N, providing you the freedom to record at your preferred resolution without concerning yourself with the final output quality. Sound Blaster X-Fi also supports digital-matched recordings in resolutions from 44.1kHz to 96kHz


Lowest Latency ASIO Recording


You'll get ASIO recording with latency as low as one millisecond and zero CPU load for the most precise audio recording capabilities in any class!



Advanced Features and Effects for Music and Audio Creation


Sound Blaster X-Fi supports up to eight different 24-bit hardware effects, all of which are accessible through the special Audio Creation Mode Interface and can be used with any of the inputs.

You will also enjoy unprecedented hardware synthesis capabilities with 24-bit SoundFont sampling!

For the first time, create multichannel MIDI ******* with 3D MIDI.









هذا الكرت هو اخر انتاج لشركة كرييتيف وانا قمت بشرائه من مدة اسبوع ولقد اعجبني جدا جدا واستطيع ان اقول انه كرت صوت احترافي بكل معنى الكلمه للمزايا التي يحتويها
السيئه الوحيده في هذا الكرت هو سعره المرتفع جدا حيث يبلغ 500 دولار



وهو يعطيك اكثر من مود لسهولة التعامل معه بسرعه

Audio Creation Mode






Gaming Mode





Entertainment Mode



مواصفاته:
Technical Specs

24-bit Analog-to-Digital conversion of analog inputs at 96kHz sample rate
24-bit Digital-to-Analog conversion of digital sources at 96kHz to analog 7.1 speaker output
24-bit Digital-to-Analog conversion of stereo digital sources at 192kHz to stereo output
16-bit to 24-bit recording sampling rates: 8, 11.025, 16, 22.05, 24, 32, 44.1, 48 and 96kHz
ASIO 2.0 support at 16-bit/44.1kHz, 16-bit/48kHz, 24-bit/44.1kHz 24-bit/48kHz and 24-bit/96kHz with direct monitoring.
Enhanced SoundFont support of up to 24-bit resolution
64MB of X-RAM
Audio Performance (Rated Output @ 2Vrms, Typical Value)

Signal-to-Noise Ratio (20kHz Low-pass filter, A-Weighted)
Stereo Output: 116dB
Front and Rear Channels: 116dB
Center, Subwoofer and Side Channels: 116dB
Total Harmonic Distortion + Noise at 1kHz (20kHz Low-pass filter) = 0.0008%
Frequency Response (-3dB, 24-bit/96kHz input ) = <10Hz to 46kHz
Frequency Response (-3dB, 24-bit/192kHz input) = <10Hz to 88kHz (Stereo only)
Connectivity

FlexiJack (Performing a 3-in-1 function, Digital I/O1 / Line In / Microphone) via 3.50mm mini jack
Line level out (Front / Rear / Side / Center / Subwoofer) via 3.50mm mini jacks
AUX_IN line-level analog input via 4-pin Molex connector on card
One AD_Link (26 pin) connector for linking to the X-Fi I/O Console (upgrade option)
I/O Console Connectivity

Two RCA jacks for coaxial SPDIF input and output
Shared Auxiliary input / Phono input via RCA stereo jacks
Two optical connectors for optical SPDIF input and output
Two standard MIDI female connectors for MIDI input and output
Headphone output and volume control via 6.35 mm (1/4-inch) stereo jack
Shared line-level analog Line/Microphone input via 6.35 mm (1/4-inch) stereo jack
Shared line-level analog Line/Hi-Z input via 6.35 mm (1/4-inch) stereo jack
DIN jack to connect Creative analog speaker systems with the wired remote control or Audio Control Pod that comes with the speakers
One AD_LINK connector for linking to the audio card